"Notice! Notice! C211 model products will be delivered tomorrow will reach 200 sets! All staff to complete the production task with quality and quantity, please actively cooperate with the relevant departments". When my workmates and I struggled day and night on the C201 Phase II production line, hearing this notice meant that all employees had to give up their weekend rest time to complete the production task. Because the production line of C211 models not only has C211 models, but also has five mature models of C201, C202, C206, S201 and C490, so the daily production tasks for the employees on this line are very heavy and face great challenges every day!

Speaking of the C211 model, I can't help but recall the days when it entered the site at the suspension point, trial production to the robot spot welding equipment site, and then to small batch production. It was the day after the May Day holiday. The tooling and fixtures of C211 model products entered the production workshop after acceptance. It was a great honor to be assigned to my production line team to be responsible for trial production. In the welding site of the spark splashing suspension point, the engineer took pains to adjust the state of the product on the fixture again and again, while the workers and the engineer cooperated to complement each other, accurately completed each welding requirement, and were busy for the common goal......

The days are turning page by page. In a twinkling of an eye, the scorching sun is scorching the earth. The heat is unbearable. In this city where we live, it is common for the temperature to exceed 40 degrees. My workmates and I are in the furnace-like workshop every day. Accompanied by the heat, the welding tongs in hand cooperate with the engineers to overcome the difficulties. Look! This group of lovely people are still wearing long-sleeved flame-retardant overalls, safety helmets, bulky goggles between the bridge of their nose, leather aprons that are not breathable at all, thick wrist guards, heat-resistant and wear-resistant canvas gloves between their fingers, and anti-smash and durable labor protection shoes under their feet. They are fully armed and busy on the production line. When working, the welding tongs in hand roll up and down, left and right, the razor in hand shaves off burrs and splashes on each welding spot, picks up a pencil and draws Arabic numerals at each welding spot, so that each product can complete the operation according to the requirements of the operation instruction and put it on the finished product rack to accept the acceptance of engineers and quality inspection. Sweat wet clothes, forehead sweat also forgot to wipe, it is so flow confused their eyes. Sparks flying around them seemed to forget the pain. At the end of the day's work, the sweat dried up and the surface of the clothes was covered with a thick layer of "salt". Both arms may be faintly sore, but there is always a smile on their faces. From that smile, it can be seen that they may be able to take a shower after work immediately, or they may have overcome several technical difficulties today, or perhaps The products produced by themselves finally meet the quality requirements. Busy days make people full, busy days make people have no time to take care of those annoying things, let people forget their troubles, let people see the light, let people always immerse themselves in small gains, and experience the joy of small victories.

At this time, the C211 robot spot welding workshop, that is, the C201 phase II production line where we are located, was renovated. This means that there are seven to eight models sharing a production line, and it also means that my workers and I have to accept greater challenges and face all unknown problems. For example, a series of problems such as the satisfaction of daily delivery between models, the deployment of personnel, the frequent change of fixtures between models, the initial debugging of equipment, the unknown quality hazards in production, and the safety hazards of employees themselves. The second hand is walking at 1.1 o'clock. A week has passed, a month has passed, and a quarter has passed... In a twinkling, the severe winter has come. At this time, most people are unwilling to get up and go to work. They are willing to put their hands into their pockets and sleep in on weekends. But there is such a group of lovely people who are not afraid of the cold and struggle day and night in the front line of C211 model production, discussing and solving one problem after another with engineers and on-site leaders. For example, a certain part is not easy to clamp, a certain part is easy to miss, a certain welding spot is twisted with burrs, a certain nut hole covers the hole, a certain station safety grating does not work, no part welding equipment on a certain fixture has welding action, a certain assembly product quality state is unstable, etc. At this time, the C211 model also ushered in small batch production, waiting for the acceptance of the main engine factory.

"Notice! Notice! 200 sets of C211 models will be delivered tomorrow, and mass production will be officially started. All production line employees must be in place on Sunday." This is the voice of the monitor. At this time, it also marks that the acceptance has passed. After more than half a year's efforts, the goods have finally been received! Here, I would like to say to them that my lovely workers on C211 production line have worked hard!

Staff Accessories Drawing Notes Shaving Prickles

Engineer inspection data

C201 Phase II Contribution by Cheng Junming